video
Automated Industrial Pallet Racking
7 Industrial Pallet Racking 2
7 industrial pallet racking 3
7 industrial pallet racking 4
7 Industrial Pallet Racking 5
1/2
<< /span>
>

Automated Industrial Pallet Racking

Automated industrial pallet racking in Q235-B / Q345 steel, combining bolted selective rack frames with rail and interface provisions for shuttle, stacker crane or guided vehicle handling. Uprights run to 11.8 m, levels adjust on a 50.8 / 75 / 76.2 mm pitch and carry 500-5000 kg UDL per level.

Products Description

Automated industrial pallet racking, also described in this catalogue as an automated pallet racking system, is the pallet handling platform a warehouse buys when manual forklift travel stops being the bottleneck. Instead of a driver collecting every pallet, the rack structure carries guide rails, shuttle cars or stacker cranes that move pallets between the storage face and a conveyor or pick station. The steel frame does the same job as a conventional selective rack - it holds pallets in level positions - but the levels are approached by machine, not by a person.

That distinction changes what the buyer has to specify. On a manual rack the questions are height, span and beam capacity. On an automated industrial pallet racking the same questions apply, but they are joined by rail gauge and straightness, shuttle or crane interface tolerances, control cabinet position, and how the structure must be levelled so a machine can engage a pallet repeatably at the twentieth level. A rack a few millimetres out of true is tolerable for a forklift operator and disruptive for an automated handling device.

This page is written for the buyer assembling an automated industrial pallet racking specification: what the steel structure has to deliver, which pallet racking configurations accept automated handling, and what has to be agreed with the automation integrator before the first frame is anchored. Most projects are phased - phase one covers the aisles with the highest throughput pressure, phase two extends the rail and control system over the remaining bays. Because the frames and beams are the same bolted product line, that later extension does not require the first phase to be rebuilt. See Future-proof expansion below for what to plan at phase one.

Automated industrial pallet racking aisle with palletised loads stored at multiple levels

Basic Info.

The table below lists the figures a buyer needs to fix before an automated industrial pallet racking layout can be drawn. Anything shown as [TBC] is confirmed against the project rather than assumed from the product family. Where an automated handling device is involved, the figures in the rail, control and installation rows matter as much as the load figures.

Storage principle

Pallet on beam levels; handled by shuttle car, stacker crane or guided vehicle rather than a driven forklift

Common configurations

Pallet shuttle / radio shuttle, AS/RS with stacker crane, guided-vehicle aisle, and hybrid racking where part of the store stays manual

Steel base used

Selective pallet racking frames and beam levels; also double deep, drive-in and live storage where the flow pattern suits automation

Main steel grade

Q235-B / Q345

Upright section

90 x 70 / 100 x 70 / 120 x 95 mm

Upright thickness

1.8 / 2.0 / 2.5 mm

Beam section

80 x 50 / 100 x 50 / 120 x 50 / 140 x 50 / 160 x 50 mm

Beam thickness

1.5 / 1.8 mm

Adjustment pitch

50.8 / 75 / 76.2 mm

Beam span

1200 - 3600 mm

Frame depth

800 - 1200 mm

Upright height

up to 11.8 m standard; taller single-piece frames quoted as a special item [TBC]

Levels per bay

2 - 20, depending on height and how the handling device reaches the level

Load capacity

500 - 5000 kg UDL per level, confirmed against span, level pitch, beam section and upright thickness

Rail / guide system

To suit the shuttle or crane supplier's specification; gauge, straightness tolerance and fixing detail confirmed per project [TBC]

Control interface

The rack is a passive steel structure; controls, WMS / WCS and safety interlocks come from the automation integrator [TBC]

Surface finish

Powder coated or hot-dip galvanized, 60 - 80 um

Standard colours

RAL 5015 blue uprights, RAL 2004 orange beams; other RAL codes on request

Pallet compatibility

Euro pallet / 1200 x 1000 / 1000 x 800 / 48 x 40 in; other sizes to drawing

Installation

Bolted assembly with floor-fixed base plates; shimming and levelling tolerances agreed with the integrator before dispatch

Load table

Issued per project against the confirmed pallet, span and level pitch

Documentation

Dimensional drawings, load table and packing list; market declarations issued on request

Lead time

15 - 30 days for the steel structure, confirmed at order

Packing

Frame parts bundled and steel-strapped on pallets; accessories in cartons or steel cases

MOQ / trade terms

One 20 ft container as a starting quantity; FOB / CIF / DAP against the destination port

Payment terms

T/T or L/C at sight, agreed at order

Price basis

Quoted per bay, per level or per tonne of structure once the configuration is fixed

Integrating Automation With the Rack Structure

Automation is not a rack accessory bolted on at the end. It is a decision that has to be made before the first upright is positioned, because it determines rail gauge, the flatness the floor must be brought to, and where power and controls will run. These are the points that decide whether an automated industrial pallet racking performs as designed. They apply whether the project is a new automated industrial pallet racking installation or a retrofit onto an existing rack run.

  • Decide the handling device first. A pallet shuttle, a stacker crane and a guided vehicle impose different loads and tolerances on the same frame. Fixing the device before the rack layout is drawn avoids rebuilding the first aisles.
  • Bring the floor to the required flatness. Automated handling needs the rack base at a consistent level. Floor flatness is surveyed and either corrected or shimmed and grouted during installation, before the frames are anchored.
  • Level the frames during erection, not after. Frames must be plumbed bay by bay as they go up. Correcting alignment once the rail system is fixed is far more disruptive than doing it in sequence.
  • Reserve the control footprint at layout stage. Control cabinets, conveyor take-away points and pick stations all consume floor area. Leaving them out of the initial layout is the most common reason an automated industrial pallet racking layout needs redesigning.
  • Design the interface as a shared responsibility. The rack supplier holds the steel structure; the integrator holds controls, drives and safety logic. Define in writing who supplies rails, fixings, cable routing and the sign-off on interface tolerances.
  • Plan inspection and clearance in an automated aisle. A person still has to reach every frame for inspection. Confirm that an aisle climbable only by machine still meets the local access and egress requirement.
  • Keep phase two in the same section family. Using the same upright sections and beam pitch in phase one means phase two is an extension, not a replacement.

Main Types of Pallet Racking and Their Automation Fit

The eight configurations below account for most pallet storage installations. The third column shows how each one behaves when it is combined with automated handling, which is the deciding factor for an automated industrial pallet racking project. The first two are the ones most commonly specified as the steel base for an automated industrial pallet racking.

Selective Pallet Racking

FIFO or LIFO

Direct access to every pallet. The usual steel base for shuttle and crane systems because every level can be addressed independently.

Very Narrow Pallet Racking

FIFO or LIFO

Built for narrow operating aisles. Compatible with guided vehicles and cranes where a conventional truck cannot work the aisle.

Double Deep Pallet Racking

FIFO or LIFO

Two pallets deep at each position. Suited to crane systems that can reach the rear position without a truck entering the aisle.

Drive in Racking

LIFO

Pallets stored inside the frame with no aisle between levels. Automated reach is limited by the depth of the lane.

Drive Through Racking

FIFO

Drive-in layout with entry at both ends. Lane depth sets how far a shuttle or crane can travel.

Live Storage Pallet Racking

FIFO

Gravity lanes feed pallets to the picking face. Works well with a shuttle or conveyor at the discharge end.

Push Back Pallet Racking

LIFO

Nested carts on inclined rails. Mechanical reloading makes automated handling less straightforward.

Mobile Pallet Racking

FIFO or LIFO

Bases travel on floor rails to open one aisle at a time. Density gain comes from opening and closing aisles, so it usually stays a manual or semi-automated solution.

The table is a starting point, not a prescription. Which of these an automated industrial pallet racking project settles on depends on how many SKUs the store holds, whether stock rotates on a first-in-first-out discipline, and how much throughput the automation is being bought to deliver.

Two configurations deserve a note. Live pallet racking combines gravity lanes with powered take-away, so the rack discharges pallets to a fixed face and the handling device only has to work one end of the lane. A pallet shuttle system or warehouse shuttle system pairs a shuttle car with the rail that runs inside the frame, and is the arrangement most buyers mean when they ask for an automated industrial pallet racking: the structure carries the rail, the shuttle does the travel, and no truck enters the aisle. Where the store also needs conventional access for slow-moving stock, a plain run of warehouse storage shelves alongside the automated bays is often the most economical answer.

Why Choose Our Automated Industrial Pallet Racking

The points below are the ones buyers raise most often when they compare an automated industrial pallet racking quotation against a conventional pallet racking quote.

  • Steel base proven in manual service. The frames and beams are the same bolted selective product that runs in warehouses without any automation. If the automation is added later or decommissioned, the rack itself remains a working pallet store.
  • Sections matched to machine-loaded levels. Upright sections of 90 x 70 to 120 x 95 mm and beam sections of 80 x 50 to 160 x 50 mm are selected against the actual load per level, not against a nominal figure.
  • Adjustment without drilling or welding. Levels re-position on a 50.8 / 75 / 76.2 mm pitch, so the level heights an automated industrial pallet racking works to can be set and later changed.
  • Depth and height that suit dense layouts. Frame depths of 800 to 1200 mm and uprights to 11.8 m support layouts that use the building height rather than the floor area.
  • Hot-dip galvanizing for demanding environments. Where the store is cold, humid or chemically exposed, galvanized steel is available alongside powder coating.
  • Load table per project. Capacity is issued against the confirmed span, level pitch and beam section rather than published as a single headline number that will not survive the actual configuration.
  • Drawing-led manufacturing. Frames are punched and beams cut to the approved layout drawing, so bays arrive in sequence and erect without on-site drilling.
  • Installation guidance for alignment. Erection sequence, plumbing and levelling requirements and floor fixing detail are provided with the drawings - which matters most where a machine has to engage a level repeatedly.
  • Documentation and declarations on request. Dimensional drawings, load table and packing list are standard. Any declaration the destination market requires is issued against the confirmed project rather than assumed from the product family.
  • Mixed-container loading. Uprights, beams and accessories can be combined in one shipment to reduce freight per tonne.
  • Spare parts held as standard sections. Replacement uprights, beams and safety clips are standard sections, so a damaged member does not require a special order.
  • Future-proof expansion. Phase two can extend the same section family, so growth in the automated area does not force the original structure to be replaced.

Applications

An automated industrial pallet racking suits operations where pallet movement is repetitive, the store is tall, and labour is either scarce, expensive or exposed to a difficult environment. The list below covers the site types that most often specify industrial racks for warehouse and distribution use.

  • High-throughput distribution centres - steady pallet flow into and out of a fixed set of positions.
  • Cold storage and freezer rooms - machine handling removes people from prolonged low-temperature work.
  • Food and beverage warehouses - FIFO discipline on dated stock supported by level-by-level addressing.
  • Pharmaceutical and medical distribution - controlled access to batch-segregated pallet positions.
  • Automotive component stores - dense storage of repetitive pallet formats feeding a line.
  • Third-party logistics (3PL) sites - layout flexibility to re-profile the store between contracts.
  • E-commerce fulfilment centres - buffer storage ahead of pick and pack stations.
  • Manufacturing raw material stores - bulk palletised input held close to the point of use.
  • Export packing and consolidation - staging pallets before container loading.
  • Spare parts and MRO stores - high SKU counts held in a compact footprint.

In all of these, the rack run is built from the same industrial racking shelves and warehouse racks used on a manual installation, which is what keeps the project scalable: the automated industrial pallet racking steel base can be extended into aisles that were originally planned for forklift service, and the same warehouse racking solutions used in the manual area can be upgraded aisle by aisle.

Components of an Automated Pallet Racking Bay

An automated industrial pallet racking bay adds a rail and interface layer to a conventional rack frame. The components below are the ones that matter when the structure has to be reached by a machine.

  • Upright frame - two uprights braced by horizontal and diagonal members; the vertical load path of the bay.
  • Upright - slotted column carrying the beam levels and the rail or guide fixings. Teardrop beams and interlock beams both seat into this column, so the punching pattern is confirmed against the beam type before manufacture.
  • Base plate - foot welded to each upright for floor anchoring and for transferring load into the slab.
  • Box beam - the horizontal member a pallet rests on, with connectors at each end.
  • Beam connector - the hook or interlock that seats the beam into the upright slot and transfers load.
  • Beam safety clip - retains the connector in the slot so beam dislodgement in service is resisted.
  • Row spacer - ties parallel frames together to stiffen the row against accidental impact.
  • Guide rail or shuttle rail - carries the shuttle car or defines the path a crane or vehicle follows.
  • Rail fixing bracket - locates and anchors the rail to the frame at the specified gauge.
  • Shuttle car or stacker crane interface - the point where the handling device engages the structure; tolerances are agreed with the integrator.
  • Floor fixing anchor - bolts the base plate to the slab at the load and uplift the layout requires.
  • Safety signage and load plate - identifies the permissible load and communicates the operating limits in the aisle.

Each bay is assembled from the same standard sections as a conventional pallet rack warehouse and shelf installation - upright, base plate, beam, connector and clip - with the rail and interface provisions added as an extra layer on the frame. That is why an automated industrial pallet racking bay can be converted from manual to automated service without replacing the steel.

Automated industrial pallet racking frame uprights with punched slots for adjustable beam levels
Box beam connection detail on an automated industrial pallet racking bay
High level pallet racking bay with pallet positions addressed level by level

Safety and Load Considerations

Load capacity for an automated industrial pallet racking is not a single figure that applies to every installation. It depends on the beam span, the level pitch, the beam section, the upright section and thickness, the pallet weight distribution and the number of loaded levels in the frame. For that reason capacity is issued as a project-specific load table for the confirmed configuration rather than stated as a headline number.

  • Load table per project. The permissible load per level is confirmed against the actual span and beam section chosen for your layout. A different span or a different beam section gives a different figure, so the load table is issued with the automated industrial pallet racking layout drawing rather than published as a catalogue number.
  • Engineering calculation. Frame and beam design is carried out against the confirmed configuration and the building conditions at the site, including the loads the handling equipment imposes on an automated industrial pallet racking structure.
  • Deflection limit stated at quotation. The deflection limit assumed in the design is stated on the quotation, so the buyer can compare proposals on the same basis.
  • Declarations on request. Where the destination market requires a declaration, test report or inspection certificate, it is issued against the confirmed project. Please confirm the destination market and the required document before order so it can be arranged.
  • Floor and fixing requirements. The load transferred into the floor and the anchoring requirement are confirmed with the layout drawing. Floor capacity and condition remain the buyer's responsibility and should be verified by a qualified engineer.
  • Installation by qualified personnel. Erection, plumbing, levelling and floor fixing should be carried out by competent installers working to the approved drawings and the site's own safety rules.
  • Protect the structure in service. Frames are designed against normal operating loads, not against impact. Impact protection at aisle ends and column positions is recommended wherever handling equipment works close to the frame.
  • Inspect and maintain. The structure should be inspected at intervals set by the site's risk assessment. Damaged or deformed members should be replaced rather than straightened.

Gallery

Range images showing the rack structures used as the steel base for an automated industrial pallet racking, together with load and connection details.

Loaded automated industrial pallet racking aisle with pallets at every level
Long pallet racking run through a distribution centre aisle
Dense high bay pallet racking using the full building height
Upright punching detail on a pallet racking frame
Bolted beam to upright connection on a pallet racking bay
Row spacer and frame bracing on a pallet racking run

Production Process

Steel sections for an automated industrial pallet racking are cut, punched and formed, then powder coated or hot-dip galvanized before packing to the approved layout drawing.

Roll formed and punched upright section ready for framing
Box beam section cut and punched to length
Finished and surface treated pallet racking frames before dispatch
  • Coil and section preparation - steel coil is levelled, slit and roll formed into upright and beam sections.
  • Punching - uprights are punched on the adjustable pitch; beams are punched for the connector and safety clip.
  • Cutting to length - sections cut to the lengths shown on the approved layout drawing.
  • Welding and assembly - uprights are welded to base plates and bracing is fitted to form the frames.
  • Surface treatment - powder coating or hot-dip galvanizing applied to the specified film specification.
  • Inspection and packing - frames checked against the drawing and bundled for loading in the sequence the site needs.

Package

Frame parts for an automated industrial pallet racking are bundled and steel-strapped on pallets, with accessories in cartons or steel cases. Bundles are marked and loaded in the sequence shown on the packing list so that erection can start without sorting the whole shipment on site.

Where galvanized or powder-coated members are shipped together, they are separated in the load to reduce abrasion in transit. Long uprights and beams are packed to fit a 20 ft or 40 ft container; mixed sections of an automated industrial pallet racking can be combined in one container to reduce freight per tonne.

Pallet racking frames bundled and steel strapped for container loading
Box beams packed in bundles for shipment
Pallet racking shipment loaded into a container

FAQ

Q: What is the delivery time for an automated industrial pallet racking?

A: Production of the steel structure is normally 15 to 30 days after the drawings are approved, followed by ocean freight to the destination port. Confirmed at order against the quantity and the destination.

Q: Can I choose the colour for the pallet racking?

A: Yes. Standard colours are RAL 5015 blue uprights and RAL 2004 orange beams. Other RAL codes can be applied, including the colours the automation integrator uses for its own equipment.

Q: What height of upright can you make?

A: Standard uprights run to 11.8 m. Taller single-piece frames can be quoted as a special item, but they affect packing, transport and how the frames are raised during erection.

Q: What is the maximum loading capacity?

A: Capacity is not a single figure. A common working range is 500 - 5000 kg UDL per level, confirmed in the load table issued against your span, level pitch and beam section.

Q: Does the rack come with the automation equipment?

A: No. An automated industrial pallet racking as supplied by us is the steel rack structure and the interface provisions for handling equipment. Shuttle cars, stacker cranes, guided vehicles and the control system are supplied by the automation integrator.

Q: Who supplies the rails and guides?

A: This depends on the integrator's specification. Rails, guide brackets and their fixing detail are agreed in writing at the drawing stage so that responsibility for interface tolerances is clear. On an automated industrial pallet racking the rail is a separate scope item from the frame.

Q: Can an existing pallet rack be converted to automated operation?

A: Sometimes, but it has to be assessed. The existing frames must meet the alignment and section requirements of the automated handling device, and the floor may need work. A survey of the existing structure is the first step in any automated industrial pallet racking retrofit.

Q: What floor flatness do I need?

A: The requirement follows from the handling device and is agreed with the integrator. It is surveyed before installation, and any correction or shimming is carried out during erection rather than after the rails are fixed.

Q: How many levels can the rack have?

A: Between 2 and 20 levels per bay depending on the upright height and how the handling device reaches the level. The limit is usually set by the building height and the machinery.

Q: Is the rack suitable for cold storage?

A: Yes, with the right steel specification and surface treatment. Hot-dip galvanized members are normally chosen for freezer and chilled environments.

Q: Do you supply installation?

A: Supervision and installation guidance are available. Erection, plumbing, levelling and floor fixing should be carried out by competent installers working to the approved drawings and the site's safety rules.

Q: What documents are provided with the shipment?

A: Dimensional drawings, load table and packing list as standard. Any declaration or inspection certificate the destination market requires is issued against the confirmed project - please confirm the destination and the required document before order.

Hot Tags: automated industrial pallet racking, China automated industrial pallet racking manufacturers, suppliers, factory, industrial racking, pallet rack decking, heavy duty metal storage shelves, garage storage shelves, cold room shelving, adjustable fork pallet jack

Send Inquiry

(0/10)

clearall